该2通道模拟量输入模块可接收0-20mA差分信号。

每个通道的输入信号经电气隔离，并以13位分辨率的形式传输。

模块由内部系统电源供电(通过内部数据总线)。

屏蔽端可直接与DIN导轨相连。

• 测量值采集：时间同步
• 测量范围上溢/下溢：状态字节与LED
• 转换方式：SAR(逐次逼近寄存器)
• 工作模式：连续采样(预设)
• 保护：非线性限制

该模块具有2个计数器，可分别独立计算二进制24 V DC脉冲数， 并将计数值通过现场总线传送至控制系统。

计数器可通过控制字节进行设置、复位和锁存。

此外，控制字节还被用于确定计数方向。

该模块是一个SSI接口，可以直接连接SSI编码器。

当该接口模块向传感器发送一个时钟脉冲后，模块读取输入数据并以数据字的形式将其直接传送至PLC或PC的过程映像区。

可通过电源跨接触点为编码器供电。

This digital output module controls actuators operating in Zone 0+1 hazardous areas.

Intrinsically safe magnetic valves can be directly controlled.

The WAGO I/O System 750 XTR must be installed either in Zone 2 or in a non-hazardous area.

All outputs are electronically short-circuit-protected.

Indicators:

• Green LED (output status)

Field and system levels are electrically isolated.

The device is ideal for operation in extreme environments thanks to:

• An extended temperature range
• Greater immunity to impulse voltages and electromagnetic interference
• Higher vibration and shock resistance

This supply module powers all intrinsically safe 750 Series Ex i Modules. It also monitors the power supply to the downstream Ex i segment and separates the intrinsically safe from the non-intrinsically safe section of the WAGO I/O System 750 XTR. The input and output sides are electrically isolated from each other.

The maximum current provided by the supply module is 1.0 A. When configuring the Ex i segment, the total current must not be exceeded.

In the event of a short circuit or overload, electronic monitoring automatically switches off the output voltage. After eliminating the fault, the output voltage is reactivated within approximately ten seconds.

If, due to load conditions, more than one supply module is required per station, four distance modules (750-616/040-000) must be placed between the intrinsically safe sections.

• Indicators:
• Green LED (input voltage)
• Green/red LED (output voltage available/not available)

The device is ideal for operation in extreme environments thanks to:

• An extended temperature range
• Greater immunity to impulse voltages and electromagnetic interference
• Higher vibration and shock resistance

该模块是一个SSI接口，可以直接连接SSI编码器。

当该接口模块向传感器发送一个时钟脉冲后，模块读取输入数据并以数据字的形式将其直接传送至PLC或PC的过程映像区。

可通过电源跨接触点为编码器供电。

该模拟量输入模块可接收±10 VDC差分信号。

每个通道的输入信号经电气隔离，并以13位分辨率的形式传输。

模块由内部系统电源供电(通过内部数据总线)。

屏蔽端可直接与DIN导轨相连。

• 测量值采集：时间同步
• 测量范围上溢/下溢：状态字节与LED
• 转换方式：SAR(逐次逼近寄存器)
• 工作模式：连续采样(预设)
• 保护：RC电路

该模块是一个SSI接口，可以直接连接SSI编码器。

当该接口模块向传感器发送一个时钟脉冲后，模块读取输入数据并以数据字的形式将其直接传送至PLC或PC的过程映像区。

可通过电源跨接触点为编码器供电。